Eec 180a | Electronic Engineering homework help

UNIVERSITY OF CALIFORNIA, DAVIS Department of Electrical and Computer Engineering EEC180A DIGITAL SYSTEMS I Fall 2015 LAB 5: COUNTER DESIGN Objective: Given a desired counting sequence, design and build the counter using flip-flops and gates. Derive the flip-flop input equations using a state table and K-maps Preparation (Pre-lab) ! Do the complete paper design for the counter specified in Design I. Your paper design must include the following items: o State transition table for the counter o K-maps for each of the flip-flop input equations. o Minimized sum of products (SoP) equation for each flip-flop input signal. Description In this lab, you will design a unique counter that implements the state diagram shown in the figure below. Each student will be given an individualized count sequence to implement. The count values X1 – X6 shown in the figure will be some sequence of the numbers 1 – 6, with each number used only once. This circuit will simulate rolling a die. Rb’ Rb’ !!!!! !!! Rb’ Reset 0 X1 X2 X3 Rb Rb Rb Rb’ Rb X6 Rb’ Rb X5 Rb’ Rb Rb X4 Rb’ Figure 1. Counter State Diagram Note that the counter has an input, Rb, which stands for “Roll button”. The counter counts as long as Rb = 1, but when Rb = 0 the counter maintains the last count value. There is one other possible state in a 3-bit counter design. For example if X1 to X6 correspond to state bits 001 to 110 and the reset state corresponds to state bits 000, the “missing” state has state bits 111. It is possible that the state machine could power-up in this state. If so, you must guarantee that the state machine does not remain stuck in this state, even when the reset switch is not pressed. Thus, the next state assignment from the missing state must be to one of the states in the count sequence, X1 to X6, or the reset state. Design I. Moore Machine with the State Bits as the Outputs Design the counter as a Moore machine where the state bits serve as the count outputs. a) Draw a state transition table and derive the input equations for implementing the counter using D flip-flops and logic gates. b) Enter your design in Quartus II. Use the 7474 or the DFF component for the D flip-flops, the 7447 component for the seven-segment display logic, INPUT and OUTPUT components and basic logic gates (AND, OR, NOT, etc.) Use an SW toggle switch for Rb and a KEY pushbutton switch for Reset. Display the output on HEX0 and turn off all the segments on HEX1-HEX7. This circuit should be clocked by the 27 MHz or 50 MHz clock signals available on the Altera DE2 board. c) Verify your design by simulating in ModelSim. Print a copy of your simulation waveforms for one complete cycle for your lab report. Set the radix to Hex for the sevensegment output signal. Have your TA verify your simulation. NOTE: In order to avoid timing violations in your gate-level simulation, you may need to make the first edge of the clock signal a fall edge rather than a rising edge as shown below. You should simulate with a clock period of 100 ns and run the simulation for 100 ns each step. Design II. Mealy Machine Design the counter as a Mealy machine. Do a complete paper design. However, you do not need to enter your design as a Quartus schematic or simulate your design. Compare the number of gates required for the Mealy machine with the number required for the Moore machine in Design I. Implementation of Design I Once your simulation for Design I works, download your design to the DE2 board and verify that your circuit works. Don’t forget to import the pin assignments!! The output will change too fast to observe the sequence while the counter is counting, but you should observe that the counter stops on numbers 1 to 6 with about equal probability. If the die seems to be ‘unfair’, check your simulation and your circuit carefully. Another debugging technique is to test your circuit with a slow clock so you can see the count sequence. (This circuit will be used as part of the final lab, so save your project files.) Have your TA verify your working circuit. Lab Report Each individual will be required to submit a lab report. Use the format specified in the “Lab Report Requirements” document available on the class web page. Be sure to include the following items in your lab report: ‰ Lab cover sheet with TA verification for circuit simulation and performance ‰ Graded pre-lab ‰ Logic design documentation (truth table, K maps, logic equations) for both designs ‰ Quartus II schematics for Design I ‰ ModelSim simulation waveforms for Design I Answer the following questions in your Lab Report: Q1: Compare Design I and Design II of the sequential circuit. Describe any advantages or disadvantages of the Moore design for this circuit. Q2: A third design for the counter circuit might use a Moore machine where the state bits were not used as the outputs. For example, the state bits might be the binary count sequence 0 – 6. How would this design would with Designs I and II (assuming your assigned count was not the straight binary count sequence 1 to 6)? Which design is likely to require the fewest gates? Justify your answer. Grading ƒ Prelab 25 points ƒ Lab Verification (Simulation) 20 points ƒ Lab Verification (Hardware) 20 points ƒ Lab Report 35 points The Lab Report grading will be as follows: • Mealy machine paper design (Design II) 10 • Question Q1 5 • Question Q2 5 • Quartus II schematic 5 • Quartus II simulation waveform for your unique count sequence 10 

Calculate the price of your order

550 words
We'll send you the first draft for approval by September 11, 2018 at 10:52 AM
Total price:
The price is based on these factors:
Academic level
Number of pages
Basic features
  • Free title page and bibliography
  • Unlimited revisions
  • Plagiarism-free guarantee
  • Money-back guarantee
  • 24/7 support
On-demand options
  • Writer’s samples
  • Part-by-part delivery
  • Overnight delivery
  • Copies of used sources
  • Expert Proofreading
Paper format
  • 275 words per page
  • 12 pt Arial/Times New Roman
  • Double line spacing
  • Any citation style (APA, MLA, Chicago/Turabian, Harvard)

Our guarantees

Delivering a high-quality product at a reasonable price is not enough anymore.
That’s why we have developed 5 beneficial guarantees that will make your experience with our service enjoyable, easy, and safe.

Money-back guarantee

You have to be 100% sure of the quality of your product to give a money-back guarantee. This describes us perfectly. Make sure that this guarantee is totally transparent.

Read more

Zero-plagiarism guarantee

Each paper is composed from scratch, according to your instructions. It is then checked by our plagiarism-detection software. There is no gap where plagiarism could squeeze in.

Read more

Free-revision policy

Thanks to our free revisions, there is no way for you to be unsatisfied. We will work on your paper until you are completely happy with the result.

Read more

Privacy policy

Your email is safe, as we store it according to international data protection rules. Your bank details are secure, as we use only reliable payment systems.

Read more

Fair-cooperation guarantee

By sending us your money, you buy the service we provide. Check out our terms and conditions if you prefer business talks to be laid out in official language.

Read more